Cisco 200-105 Practice Exam Questions

Various topics about LAN switching technologies, IPv4 and IPv6 routing technologies and WAN technologies appear in this 200-105 exam.

Try it Latest DumpsSchool 200-105 Exam dumps. Buy Full File here: https://www.dumpsschool.com/200-105-exam-dumps.html (691 As Dumps)

Download the DumpsSchool 200-105 braindumps from Google Drive: https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view (FREE VERSION!!!)

Question No. 1

Which name describes an IPv6 host-enabled tunneling technique that uses IPv4 UDP, does not require

dedicated gateway tunnels, and can pass through existing IPv4 NAT gateways?

Answer: D

Question No. 2

What does it take for BGP to establish connection? (Choose two.)

Answer: B, C

Question No. 3

What are the Popular destinations for syslog messages to be saved? (Choose three.)

Answer: B, C, E

Question No. 4

Refer to the exhibit. What can be concluded from the output of the debug command?

Answer: C

Question No. 5

What does a router do if it has no EIGRP feasible successor route to a destination network and the successor route to that destination network is in active status?

Answer: C

Introduction to EIGRP

http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080093f07.shtml

Feasible Successors

A destination entry is moved from the topology table to the routing table when there is a feasible successor. All minimum cost paths to the destination form a set. From this set, the neighbors that have an advertised metric less than the current routing table metric are considered feasible successors.

Feasible successors are viewed by a router as neighbors that are downstream with respect to the destination.

These neighbors and the associated metrics are placed in the forwarding table.

When a neighbor changes the metric it has been advertising or a topology change occurs in the network, the set of feasible successors may have to be re-evaluated. However, this is not categorized as a route recomputation.

Route States

A topology table entry for a destination can have one of two states. A route is considered in the Passive state when a router is not performing a route recomputation. The route is in Active state when a router is undergoing a route recomputation. If there are always feasible successors, a route never has to go into Active state and avoids a route recomputation.

When there are no feasible successors, a route goes into Active state and a route recomputation occurs. A route recomputation commences with a router sending a query packet to all neighbors. Neighboring routers can either reply if they have feasible successors for the destination or optionally return a query indicating that they are performing a route recomputation. While in Active state, a router cannot change the next-hop neighbor it is using to forward packets. Once all replies are received for a given query, the destination can transition to Passive state and a new successor can be selected.

When a link to a neighbor that is the only feasible successor goes down, all routes through that neighbor commence a route recomputation and enter the Active state.

Question No. 6

You attempt to execute the APIC-EM ACL path trace feature without specifying the protocol. How does the

ACL path trace respond?

Answer: A

Question No. 7

A network administrator is configuring the routers in the graphic for OSPF. The OSPF process has been started and the networks have been configured for Area 0 as shown in the diagram. The network administrator has several options for configuring RouterB to ensure that it will be preferred as the designated router (DR) for the 172.16.1.0 /24 LAN segment.

What configuration tasks could be used to establish this preference? (Choose three.)

Answer: A, C, E

Question No. 8

Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are

operating at the same bandwidth? (Choose three.)

Answer: B, C, D

Question No. 9

What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance?

Answer: B

Netflow can be used to diagnose slow network performance, bandwidth hogs and bandwidth utilization quickly with command line interface or reporting tools.

http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-netflow/prod_white_paper0900aecd80406232.html

Question No. 10

Refer to the output from the show running-config command in the exhibit. What should the administrator do to allow the workstations connected to the FastEthernet 0/0 interface to obtain an IP address?

Answer: C

Question No. 11

Which function does traffic shaping perform?

Answer: D

Question No. 12

Which feature or value must be configured to enable EIGRPv6?

Answer: C

The configuration of EIGRP for IPv6 has some restrictions; which are:

The interfaces can be directly configured with EIGRP for IPv6, without the use of a global IPv6 address.

There is no network statement in EIGRP for IPv6.

The router ID needs to be configured for an EIGRPv6 protocol instance before it can run.

EIGRP for IPv6 has a shutdown feature. Ensure that the routing process is in “no shut” mode in order to

run the protocol.

https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocoleigrp/

113267-eigrp-ipv6-00.html

Question No. 13

A network administrator is configuring ACLs on a Cisco router, to allow traffic from hosts on networks

192.168.146.0, 192.168.147.0, 192.168.148.0, and 192.168.149.0 only.

Which two ACL statements, when combined, are the best for accomplishing this task? (Choose two.)

Answer: A, C

Question No. 14

Which type of interface can negotiate an IP address for a PPPoE client?

Answer: B

200-105 Dumps Google Drive: (Limited Version!!!)
https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view

Related Certification: CCNA Routing & Switching dumps

Facebook Comments