Try Dell DNDNS-200 Exam Questions – (March-2018 Dumps)

Due to rapidly growing in IT industry the Dell DNDNS-200 exam is very important for your professional life. You can pass Dell DNDNS-200 exam easily with RealExamDumps’s latest DNDNS-200 exam questions. We at RealExamDumps provide you latest DNDNS-200 exam questions that are going to be asked in the exam so if you prepare and practice the same DNDNS-200 questions beforehand it would be easier for you to answer them in the real exam. When you will become DNDNS-200 exam certified then you will exel in Networking Installation & Configuration. All Dell DNDNS-200 exam questions prepared by the subject matter experts who are professional in their respective fields.

♥ VALID DNDNS-200 Exam Questions 2018 ♥

DNDNS-200 exam questions, DNDNS-200 PDF dumps; DNDNS-200 exam dumps:: (60 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest Dell DNDNS-200 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

Which three components can be used to deploy 10GbE N-Series switches in a user-port stack configuration? (Choose three.)

A. SAS Cables
B. Standard Ethernet Cables
C. Dedicated stacking modules
D. TwinAx Cables
E. Optical Transceivers

Answer: A,D,E

Question: 22

A network deployment engineer needs to deploy four Dell Networking N1500 series switches. All switches are to be stacked together using 10Gbe ports on each switch and implement OSPF per the deployment plan. The customer has been shipped only the four switches with SAS stacking cables. No other equipment has been shipped.
Which two issues occur when the network engineer tries to stack all four switches and implement OSPF? (Choose two.)

A. Incorrect cabling was shipped for stacking instead of the required 10Gbs TwinAx.
B. The N1500 series switches do not support advanced Layer 3 Functionality.
C. The N1500 series switches support Layer 3 lite Functionality.
D. Stacking is limited to only four switches because of the limited back-plane bandwidth.
E. Stacking modules were provided as per the deployment.

Answer: A,C

Dell Networking N1500 Series switches stack using the 10G SFP+ front-panel ports.
N1500 does not support OSPF.
Dell Networking N-Series N1500, N2000, N3000, and N4000 Switches User’s Configuration Guide. Page 193.

Question: 23

Refer to the exhibit.
A network engineer is called onsite to troubleshoot replication failure and traffic loss. Whenever replication occurs between SAN A and SAN B, users report traffic loss between sites, and replication ultimately fails due to traffic loss.
Based on the topology shown, what is the most likely cause of the traffic loss?

A. Traffic needs to be policed on the site border routers.
B. An inbound policy map needs to be defined on the site border that marks the replication traffic with a DSCP value of 46.
C. An outbound policy map needs to be defined on the site border that marks the replication traffic with a DSCP value of 46.
D. Traffic needs to be shaped on the site border routers.

Answer: C

In Quality of Service, DSCP value 46 is high-priority traffic.

Question: 24

Refer to the exhibit of the N-series switches.
The exhibit shows a Layer 2 network between Host A (a Desktop Computer running Windows 7) and Host B (another Desktop Computer running Windows 7) and the list of VLANs Untagged (U) and Tagged (T) at each Ethernet interface: Host A transmits an Ethernet frame untagged on VLAN 1.
What will happen to the Ethernet frame?

A. SW2 drops the Ethernet frame when trying to transmit it out of interface E2 because the incoming and outgoing interfaces are Tagging/Untagging VLAN 1 differently.
B. The Ethernet frame is successfully delivered to Host.
C. STP drops the Ethernet frame because it cannot create an end-to-end loop free path between the switches for VLAN 1.
D. VLAN consistency protocol determines that the VLAN is not correctly Tagged/Untagged on all interfaces, an error will occur, and SW1 will drop the frame on interface E2.

Answer: B

Question: 25

Refer to the exhibit.
Considering the network topology and information shown, what is an issue with end point devices in network that try to route to

A. ICMP Redirects
B. Suboptimal Routing
C. Routing Loop
D. Summarization Black Hole

Answer: C

Question: 26

Refer to the Exhibit.
A network engineer receives the output shown when removing MLAG from a pair of N-Series switches.
Which sequence of steps must the engineer complete to remove the vpc peer-link from Port Channel 1?

A. Shut down the Port Channel interfaceIssue the no vpc peer-link command on the Port Channel
B. Remove the vpc feature using the no feature vpc commandIssue the no vpc peer-link command on the Port Channel
C. Remove the channel-group command from all members of the Port ChannelIssue the no vpc peer-link command on the Port Channel
D. Remove peer-keepalive enable using the no peer-keepalive enable commandIssue the no vpc peer-link command on the Port Channel

Answer: D

New Updated DNDNS-200 Exam Questions DNDNS-200 PDF dumps DNDNS-200 practice exam dumps:

Facebook Comments