Try IBM C9010-022 Exam Questions – (Dec-2017 Dumps)

Due to rapidly growing in IT industry the IBM C9010-022 exam is very important for your professional life. You can pass IBM C9010-022 exam easily with RealExamDumps’s latest C9010-022 exam questions. We at RealExamDumps provide you latest C9010-022 exam questions that are going to be asked in the exam so if you prepare and practice the same C9010-022 questions beforehand it would be easier for you to answer them in the real exam. When you will become C9010-022 exam certified then you will exel in Storage Management All IBM C9010-022 exam questions prepared by the subject matter experts who are professional in their respective fields.

C9010-022 PDF dumps; C9010-022 exam dumps:: https://www.dumpsschool.com/C9010-022-exam-dumps.html (62 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate IBM C9010-022 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

How can an administrator enable the Workload Partitions Manager feature after AIX 7 has been installed with the default options?

A. Change AIX License using chlicense -I command
B. Change AIX edition using chedition -e command
C. Change WPAR License using chwpar -I command
D. Change WPAR edition using chwpar-e command

Answer: B

Question: 22

The cfgmgr command appears to be taking an excessive time to complete. The administrator was able to quit the command and return to the command prompt. The administrator does not have access to the managing HMC and unable to check for any LED codes.
How else can the cause of the observed delay be determined?

A. Review the latest entry within /var/log/cfgdb.out.
B. Start the syslog daemon before re-issuing the command.
C. Re-issue the command with the W flag.
D. Initiate the ledmon command from a separate session, then re-issue cfgmgr.

Answer: C

Question: 23

New Updated C9010-022 Exam Questions C9010-022 PDF dumps C9010-022 practice exam dumps: https://www.dumpsschool.com/C9010-022-exam-dumps.html

A host has a single virtual Ethernet adapter (ent0) configured with only a default PVID, and the administrator is trying to determine why it cannot be used to reach any other system on the network. He suspects that it may be caused by a problem in the VLAN configuration.
How would the administrator determine the VLAN for which the adapter was configured?

A. Use the command ‘Isdev -I ent0’ on the host to determine the port VLAN ID.
B. Use the command ‘Isattr-EI ent0’ on the host to determine the port VLAN ID.
C. Look on the HMC to determine which VLAN is configured for the adapter.
D. Examine the Shared Ethernet Adapter on the Virtual I/O Server to determine which VLAN the adapter is using.

Answer: C

Question: 24

How can an administrator disable Role Based Access Control (RBAC) in a WPAR?

A. Run chattr -E -I sys0 -a enhanced_RBAC=false
Reboot the WPAR
B. Run the RBAC wizard and deselect ‘Enable RBAC
Reboot the system
C. Run chdev -I mywpar -a enhanced_RBAC=false
Reboot the Global Environment
D. Run chwpar -a RBAC=false
Reboot the WPAR

Answer: C

Question: 25

After performing a NIM rte install, the administrator noticed that not all filesets are at the correct Technology Level (TL). What action will help the administrator determine why the inconsistent fileset levels were installed?

A. On the NIM server, run an Ippchk to identify if the Software Vital Product Data is valid.
B. On the NIM client, run oslevel command against the TL to identify missing prerequisites.
C. Run instfix command on NIM client to determine what filesets are inconsistent.
D. On the NIM server run the NIM IsIpp command to indentify downlevel filesets contained in the lpp_source.

Answer: D

Question: 26

What is a requirement for Live Partition Mobility?

A. The network and disk must be virtual.
B. The disk must be virtual and a Logical Host Ethernet Adapter (LHEA) for network.
C. The client partition must be connected to a SAN.
D. The client partition must be set up as a ‘Mover Service Partition’.

Answer: A

Facebook Comments